Fuel |
|
Petrol |
Construction Year |
|
1936-1940 |
Bore |
|
73 x .. mm (73,02 x .. mm) |
Number of cylinders |
|
6 |
Compression ratio |
|
8 : 1 |
Engine content CC |
|
2664 (2500) |
Engine type |
|
Standard 2.5 Litre - S6 - DOHC S6 - Jaguar 2.5 2500 |
Car type |
|
Jaguar 2.5 Litre Motor 2.5 S6 (1936-1940) Mark IV Pre War Series (2.5) - Jaguar 2-1/2 Litre - Oldtimer Classics |
HP |
|
102 |
Cylinder Liner |
|
MKL op aanvraag - 73 mm - std (1936-1940) |
Piston |
|
MKP 05-11309-0 - 73,02 mm - std 1,00 (1936-1940) |
Piston |
|
MKP 05-11309-0 - 73,02 mm - 0.50 - 1.00 - 1.50 |
Piston Rings |
|
MKPR 06-01226-0 - ø 73 mm - 2.38 - 2.38 - 4.76 mm - std |
Piston Rings |
|
MKPR 06-01226-0 - ø 73 mm - 2.38 - 2.38 - 4.76 mm - 0.50 - 1.00 - 1.50 |
Exhaust Valve |
|
MKEV 01-08663-0 - 34,1x7,9x145 mm std (6x) |
Valve guide exhaust |
|
MKEG 02-08602-0 - 15,9x7,9x82,8 mm std (6x) |
Valve guide intake |
|
MKIG 02-08602-0 - 15,9x7,9x82,8 mm std (6x) |
Valve intake |
|
MKIV 01-08662-0 - 37,3x7,9x146 mm std (6x) |
Various engine parts |
|
Op aanvraag - On request - std |
Conrod Bearings |
|
MKCB 04-00360-0 - std (48,2mm) |
Conrod Bearings |
|
MKCB Op aanvraag - 04-00360-0 - 04-00362-0 - 0.25 - 0.50 - 0.75 - 1.00 |
Main Bearings |
|
MKMB 04-00361-0 - std (63mm) (< 1945) |
Main Bearings |
|
MKMB Op aanvraag - 04-00362-1 - 04-00363-0 - 0.25 - 0.50 - 0.75 - 1.00 (< 1940) |
Small end bearings |
|
MKSB Op aanvraag - std ..mm (6x) |
Crankshaft seal ring behind |
|
op aanvraag - .. mm std |
Crankshaft seal ring front |
|
op aanvraag - .. mm std |
Gasket various |
|
Op aanvraag - On request |
Headgasket |
|
MKHG 03-P0098-5 - std |
Head gasket set |
|
MKHS Op aanvraag - On request - 03-P0098-1 - std |
Gasketset complete |
|
Op aanvraag - On request - 03-P0098-0 - std |
Piston Pin Bushings |
|
MKSB Op aanvraag - std ..mm (6x) |
Parts |
|
Components not found? Request at comments! |
Operations |
|
Cylinderhead skimming |
Operations |
|
Valveseat refacing |
Operations |
|
Valve grinding |
Operations |
|
Fitting new guides |
Operations |
|
Place new hardened valve seats |
Operations |
|
Cylinderhead testing for cracks |
Operations |
|
Mounting / Assembly/ of valves |
Operations |
|
Valves adjusting (non-hydraulic) |
Operations |
|
Block skimming |
Operations |
|
Cylinder drilling |
Operations |
|
Placing new cylinders |
Operations |
|
Block testing for cracks |
Operations |
|
Crankshaft grinding |
Operations |
|
Crankshaft balancing |
Operations |
|
Crankshaft nitriding |
Operations |
|
Small end bushing replacement conrod |
Operations |
|
Connecting-rod check for straightness |
Operations |
|
Checking groundbore connecting-rod |
Operations |
|
Line boring engine |
Operations |
|
Welding / crack repair |
Operations |
|
Revision not found? Request at comments! |
Operations |
|
Complete engine overhaul ( make an appointment ) |