motorenrevisie Enginerebuilding motoren instandsetzung

Fiat 500 Topolino A 0.6 (S4) (1936-1948)

Quick Overview

Engine type: 0.6 L - OHV S4 - Fiat 0.6
Construction Year: 1936-1948
Number of cylinders: 4
Bore ø: 52 mm
Engine content: 569 CC
Compression ratio: 8 : 1
HP: 13

Parts

Fuel Petrol
Construction Year 1936-1948
Bore 52 x .. mm
Number of cylinders 4
Compression ratio .. (8 : 1)
Engine content CC 569 (500 - 600)
Engine type 0.6 L - OHV S4 - Fiat 0.5 0.6 600
Car type Fiat 500 Topolino A 0.6 S4 (1936-1948) 500 Topolino Pre War Series (0.6) - Fiat 500A Topolino - Oldtimer Classics
HP 13
Cylinder Liner MKL op aanvraag - 52 mm - std (1936-1948)
Piston MKP 05-11663-0 - 52 mm - std 1,00 (1936-1948)
Piston MKP 05-11663-0 - 52 mm - 0.50 - 1.00 - 1.50
Piston MKP 05-11663-0 - 52 mm - 2.00 - 2.50
Piston Rings MKPR 06-01708-0 - ø 52 mm - 2.00 - 2.00 - 2.00 - 3.00 mm - std
Piston Rings MKPR 06-01708-0 - ø 52 mm - 2.00 - 2.00 - 2.00 - 3.00 mm - 0.50 - 1.00 - 1.50 - 2.00 - 2.50
Exhaust Valve MKEV 01-00547-0 - 20,5x6x88 mm std (4x)
Valve guide exhaust MKEG 02-01702-0 - 12x6x47 mm std (4x)
Valve guide intake MKIG 02-01702-0 - 12x6x47 mm std (4x)
Valve intake MKIV 01-00546-0 - 22x6x88 mm std (4x)
Various engine parts Op aanvraag - On request - std
Conrod Bearings MKCB 04-00344-0 - std (45mm)
Conrod Bearings MKCB 04-00344-0 - 0.25 - 0.50 - 0.75 - 1.00
Conrod Bearings MKCB 04-00344-0 - 1.25 - 1.50
Main Bearings MKMB 04-M2072-0 - std (40mm)
Main Bearings MKMB 04-M2072-0 - 0.25 - 0.50 - 0.75 - 1.00
Small end bearings MKSB Op aanvraag - std ..mm (set)
Crankshaft seal ring behind op aanvraag - .. mm std
Crankshaft seal ring front op aanvraag - .. mm std
Gasket various Op aanvraag - On request
Headgasket MKHG 03-?????-5 - std
Head gasket set MKHS Op aanvraag - On request - 03-?????-1 - std
Gasketset complete Op aanvraag - On request - 03-?????-0 - std
Piston Pin Bushings MKSB Op aanvraag - std ..mm (set)
Parts Components not found? Request at comments!
Operations Cylinderhead skimming
Operations Valveseat refacing
Operations Valve grinding
Operations Fitting new guides
Operations Place new hardened valve seats
Operations Cylinderhead testing for cracks
Operations Mounting / Assembly/ of valves
Operations Valves adjusting (non-hydraulic)
Operations Block skimming
Operations Cylinder drilling
Operations Placing new cylinders
Operations Block testing for cracks
Operations Crankshaft grinding
Operations Crankshaft balancing
Operations Crankshaft nitriding
Operations Small end bushing replacement conrod
Operations Connecting-rod check for straightness
Operations Checking groundbore connecting-rod
Operations Line boring engine
Operations Welding / crack repair
Operations Revision not found? Request at comments!
Operations Complete engine overhaul ( make an appointment )