motorenrevisie Enginerebuilding motoren instandsetzung

Packard 120 - 8 - 282CI (1935-1940)

Quick Overview

Engine type: ..cc - Packard (USA) S8 Eight Engine
Construction Year: 1935-1940
Number of cylinders: 8
Bore ø: .. mm (3.250 in)
Engine content: .. CC
Compression ratio: .. : 1
HP: ..

Parts

Fuel Petrol
Construction Year 1935-1940
Bore .. x .. mm - (3.250 x .. in)
Number of cylinders 8
Compression ratio .. : 1
Engine content CC ..
Engine type ..cc - 8cyl - Packard (USA) S8 Straight Eight Engine 0.0 0000
Car type Packard 8 - 282CI (1935-1940) 0.0 Series (0.0) - Packard Eight - 282 CI - Oldtimer Classics - 1935-1940 (0.0)
HP ..
Cylinder Liner MKL op aanvraag - .. mm (3.250 in) - std (1935-1939-1940)
Piston MKP E153-8 - .. mm (3.250 in) - std (1935-1939-1940)
Piston MKP E153-8 - .. mm (3.250 in) - 0.20 - 0.30 - 0.40 - 0.60 - 0.80 (1935-1939-1940)
Piston Rings MKPR op aanvraag - ø .. mm (3.250 in) - .. mm std (8x)
Exhaust Valve MKEV S990 - .. mm std (8x)
Valve guide exhaust MKEG G481 - .. mm std (8x)
Valve guide intake MKIG G481 - .. mm std (8x)
Valve intake MKIV V992 - .. mm std (8x)
Various engine parts Op aanvraag - On request - std
Various engine parts TC306 - TC303 - Distributieketting - Timing Chain
Various engine parts VS424 - Klepveren - Valve Spring (16x)
Conrod Bearings MKCB CB183 - std
Conrod Bearings MKCB CB183 - 0.10 - 0.20 - 0.30
Main Bearings MKMB MS200 - std
Main Bearings MKMB MS200 - 0.10 - 0.20 - 0.30
Camshaft bearing set PA-2 - std
Small end bearings MKSB PB720 - std ..mm (8x)
Crankshaft seal ring behind op aanvraag - .. mm std
Crankshaft seal ring front op aanvraag - .. mm std
Gasket various op aanvraag - on request
Headgasket MKHG E993C - E993CS - E993S - std (1935-1940-1947)
Head gasket set MKHS op aanvraag - std
Oil Pump PK-1000 (Kit)
Piston Pin Bushings MKSB PB720 - std ..mm (8x)
Parts Components not found? Request at comments!
Operations Cylinderhead skimming
Operations Valveseat refacing
Operations Valve grinding
Operations Fitting new guides
Operations Place new hardened valve seats
Operations Cylinderhead testing for cracks
Operations Mounting / Assembly/ of valves
Operations Valves adjusting (non-hydraulic)
Operations Block skimming
Operations Cylinder drilling
Operations Placing new cylinders
Operations Block testing for cracks
Operations Crankshaft grinding
Operations Crankshaft balancing
Operations Crankshaft nitriding
Operations Small end bushing replacement conrod
Operations Connecting-rod check for straightness
Operations Checking groundbore connecting-rod
Operations Line boring engine
Operations Welding / crack repair
Operations Revision not found? Request at comments!
Operations Complete engine overhaul ( make an appointment )