motorenrevisie Enginerebuilding motoren instandsetzung

Packard V8 - 352CI (1955-1956)

Quick Overview

Packard V8 Motor Engine
Engine type: ..cc - Packard (USA) V8 Engine
Construction Year: 1955-1956
Number of cylinders: 8 - V8
Bore ø: .. mm (4.0000 in)
Engine content: .. CC (352CI)
Compression ratio: .. : 1
HP: ..

Parts

Fuel Petrol
Construction Year 1955-1956
Bore .. x .. mm - (4.0000 x .. in)
Number of cylinders 8 - V8
Compression ratio .. : 1
Engine content CC .. (352CI)
Engine type ..cc - 8cyl - Packard (USA) V8 Engine 0.0 0000
Car type Packard V8 - 352CI (1955-1956) 0.0 Series (0.0) - Packard V8 - 352 CI - Oldtimer Classics - 1955-1956 (0.0)
HP ..
Cylinder Liner MKL op aanvraag - .. mm (4.0000 in) - std (1955-1956)
Piston MKP op aanvraag - .. mm (4.0000 in) - std (1955-1956)
Piston MKP op aanvraag - .. mm (4.0000 in) - 0.20 - 0.30 - 0.40 - 0.60 - 0.80 (1955-1956)
Piston Rings MKPR SRH139 - ø .. mm (4.0000 in) - .. mm std (8x)
Exhaust Valve MKEV S2113 - .. mm std (8x) (1955-1956)
Valve guide exhaust MKEG Op aanvraag - .. mm std (8x) (1955-1956)
Valve guide intake MKIG Op aanvraag - .. mm std (8x) (1955-1956)
Valve intake MKIV V2114 - .. mm std (8x) (1955-1956)
Various engine parts Op aanvraag - On request - std
Various engine parts TC346 - Distributieketting - Timing Chain
Various engine parts VS735 (1955) - VS772 (1956) Klepveren - Valve Spring (16x)
Conrod Bearings MKCB Op aanvraag - On request - std
Conrod Bearings MKCB Op aanvraag - On request - 0.10 - 0.20 - 0.30
Main Bearings MKMB MS1696 - std
Main Bearings MKMB MS1696 - 0.10 - 0.20 - 0.30 - 0.40 - 0.60
Camshaft bearing set PA-6
Small end bearings MKSB op aanvraag - std ..mm (8x)
Valve lifter VL13 (16x)
Crankshaft seal ring behind op aanvraag - .. mm std
Crankshaft seal ring front op aanvraag - .. mm std
Gasket various op aanvraag - on request
Headgasket MKHG Op aanvraag - On request - std
Head gasket set MKHS op aanvraag - std
Piston Pin Bushings MKSB op aanvraag - std ..mm (8x)
Parts Components not found? Request at comments!
Operations Cylinderhead skimming
Operations Valveseat refacing
Operations Valve grinding
Operations Fitting new guides
Operations Place new hardened valve seats
Operations Cylinderhead testing for cracks
Operations Mounting / Assembly/ of valves
Operations Valves adjusting (non-hydraulic)
Operations Block skimming
Operations Cylinder drilling
Operations Placing new cylinders
Operations Block testing for cracks
Operations Crankshaft grinding
Operations Crankshaft balancing
Operations Crankshaft nitriding
Operations Small end bushing replacement conrod
Operations Connecting-rod check for straightness
Operations Checking groundbore connecting-rod
Operations Line boring engine
Operations Welding / crack repair
Operations Revision not found? Request at comments!
Operations Complete engine overhaul ( make an appointment )